inlet manifold.

dread · Post by **dread** » Sun Nov 06, 2011 3:21 pm

as per the headline Ta. its for a pit bike engine. so it don't need to be inline to reach original air box. can be side mouthed. thanks.

Lister · Post by **Lister** » Sun Nov 06, 2011 5:04 pm

i dont have any around but seen this on ebay carnt be bad for £3.50

http://www.ebay.co.uk/itm/pit-bike-carb ... 3a6c193009

Lister

Cerberus73 · Post by **Cerberus73** » Mon Nov 07, 2011 10:19 pm

dread i got heaps, what size u needing, for what size of motor, cover the post n ya can has one.. u need the plastic spacer as well?

dread · Post by **dread** » Mon Nov 07, 2011 10:59 pm

ok cheers boys. was hoping my mikuni would have turned up today. its off a Suberbyke RMR 125 trialy thing, now speaking with a few folks, it seems the 26 is a 22, but it could also be a 26, so untill it comes. and measure it,

i am in the dark a bit mesen. knowing my bleeding luck, it will turn out to be 19, and of no use to me.

http://www.ebay.co.uk/itm/130593685977? ... 1439.l2649
so i shall upon its arival, post up the sizes. thanks.

dread · Post by **dread** » Mon Nov 07, 2011 11:01 pm

Cerberus73 wrote:dread i got heaps, what size u needing, for what size of motor, cover the post n ya can has one.. u need the plastic spacer as well?

tizz a reworked big bor fat headed 125 posted a pic of the carb i bought. but i only have the bar info on the auction to go on as yet mesen.

Cerberus73 · Post by **Cerberus73** » Tue Nov 08, 2011 5:31 am

Ah right most the carb manifolds i have are off 110cc pit bike engines, think the carbs on some of them are 26mm jobs, so if your carb is 24-26mm should work just fine. i will give a couple a clean up and get the vernier out to check dimensions for ya.

Cerberus73 · Post by **Cerberus73** » Tue Nov 08, 2011 6:18 am

ok got hold of largest one i have, its 24mm bore so will be fine for 24mm carb, its the side angled one, so fine for a chop but no use on a standard cub, bores nice and smooth compared to some of them I've seen. and the silver paint on it is flaky, so could do with a repaint. but its yours if you want it along with its plastic spacer piece. just gimme your address in a pm and cover my postage, can't see it being more than about 3 or 4 quid to post it, probably less. paypal is fine for the postage. will let you know how much it is once i send it.

dread · Post by **dread** » Tue Nov 08, 2011 11:13 am

right the porting on the head is lapped in 26.5 down to 25. so should be able to match that i should think. still waiting on the bleedin carb.

Cerberus73 · Post by **Cerberus73** » Tue Nov 08, 2011 7:37 pm

well your welcome to it. heres a pic of the said parts. gave it a clean up for you.

dread · Post by **dread** » Tue Nov 08, 2011 7:59 pm

ta pal, as per p/ms send it up, wee the coil, and i'll ping you some paypal. will need your account email remember. have sent my address to you.

C90Club.co.uk

inlet manifold.

inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.

Re: inlet manifold.